As skateboarding becomes popular, so does doing and recreating the same stunts on a fingerboard. You, too, can surprise your friends and family by doing astonishing feats with the Tech Deck fingerboard. For most skateboarders, mastering the ollie is an excellent place to start since it serves as the basis for almost any trick on the board.
Yes, ollies may be challenging, but you can substantially shorten your learning curve with a solid grasp of the motion. What’s the trick? The ollie consists of simply two steps: the pop and the slide. Before attempting to learn how to ollie, you should be comfortable riding, turning, and tic tacs. So, why not begin by learning how to ollie like a pro?
How To Do An Ollie On A Tech Deck?
1. Finger Positioning
Place your index finger in the center of the board, between the plate nails, and your middle finger on the tail. The top two joints of the finger must be put on the board, while the third joint must not place on the board surface.
2. Kick Up The Fingerboard
The direction in which the fingerboard pushes is critical, particularly for novices. Remember to slide the fingerboard back first, then apply force to the middle finger and point to the table.
Turn the wrist, let the board spin over, and support it with two fingers; throughout this procedure, the board will always slide back. Someone may discover that the board cannot flip over; this is the most challenging portion, and Ollie’s spirit also includes this.
First and foremost, everyone pushes the board to slide back, applying force to the board, but the sliding track must be straight.
3. Raise The FINGERBOARD To An Angle Of 80 Degrees.
Slide the fingerboard backward, push the middle finger down, use the back wheel as a fulcrum, tilt the fingerboard head, and raise the index finger and the board. Maintain an angle of 80 degrees. The harder you slide back, the higher the force.
Turn your wrist and retract your middle finger, using your index finger as a fulcrum. Turn two fingers, palm, wrist, and fingerboard simultaneously to learn force coordination. Allow the fingerboard to rest on your finger.
4. Flick The Front Finger And Wrist Forward
Because the fingerboard is vertical after popping, pushing the index finger upward toward the nose raises the fingerboard for ventilation. A helpful method is concentrating on the whole hand and wrist movement rather than just the index finger.
5. Release The Fingerboard Into The Air
Turn your wrist horizontal again while controlling the board’s tail with your middle finger.
6. Set Down The Fingerboard
Finally, push the board downward to make the wheel land. Ollie will finish perfectly. You may attempt to ollie over gaps and obstacles after leaning the ollie. It is a fantastic place to begin learning with solution different great methods.
Ollie With Two Fingers
Arrange the instructions according to the Tech Deck. Place your index finger on the front skateboard, and keep the skateboard on the floor.- You will perform the trick using your dominant hand. Use the same hand’s middle finger on the rear skateboard (tail).
- We will first place two fingers on the skateboard and then push down. So wiggle the board around.
- Bring your index finger forward towards the “T” on the Tech Deck while you do so.
- When the board is in the air, apply mild pressure at the front. Push the rear panel down with two fingers while high in the air.
- Land with both fingers and continue skating forward. If your fingertips slip off the board, you pull them back in position even board is moving.
- Try executing an ollie higher than previously as you improve at this move.
Ollie With Three Fingers
Arrange the board according to the instructions. This technique will need three fingers: index, middle, and ring.- Place your index finger at the rear of the front screws while keeping the skateboard on the floor.
- Put your middle finger emblem on the board.
- Finally, the ring finger will place at the bottom of the board.
- First, we will examine what all three fingers do on the skateboard when squeezed down. So wiggle the board around.
- Watch what happens on the board, and press down on all three fingers one at a time.
- To do this feat with three fingers, we will slam first at the rear board.
- Smack the tail with your ring finger while pushing the board ahead.
- When you strike the board’s tail, it will rise into the air and go ahead.
- You attempt to land the board with all three fingers as you go ahead.
- Finally, all you have to do is ride the board ahead once it has landed.
You can learn to kickflip and flip trick on a Tech Deck now that you understand how these maneuvers operate. When you have time, brush up on your talents and see how everyone around you is amazed.
You may also teach your friends these tricks and have a little competition to see who can accomplish the most tricks.
Conclusion
Trying to execute an Ollie on a fingerboard or a Tech Deck doesn’t seem as simple as it should be. Alternatively, are you a person who needs to do stunts with three fingers instead of only two? With some practice, you can easily do an ollie on a fingerboard with three fingers.
It’s a beginner’s fingerboard technique, Ollie. It stimulates the motion of bouncing the skateboard up by employing the time difference between the twin pedals while sliding when playing a regular skateboard.
It’s a must-learn talent because, with enough practice, you can do several spectacular movements like flipping in the air and crossing barriers.